CSF is starting 2021 with a bang.
Introducing a truly collaborative effort exemplifying the best in the performance aftermarket industry, 100% designed and manufactured in the USA.
CSF’s new McLaren 720S/765LT High-Performance Intercooler System – the new advantage for the absolute best quarter-mile traps and half-mile speeds, designed for the fastest and most powerful McLarens in the world.
CSF’s Most Extensive R&D Process Yet
Initially designed by CSF R&D partner RK Autowerks using state-of-the art 3D scanning and prototyping equipment, we incorporated a massive custom-spec CSF bar/plate air-to-water core that is 68% larger than the OEM unit. Voodoo Autosport was then consulted to further enhance the design for a complete drop-in fit installation that is truly plug-and-play. Lastly, but not least, CSF reached out to the best tuners of the world’s fastest McLarens, M Engineering, to performance test the coolers. Final results: 99% efficiency (vs. OEM 94%) along with lower pressure drop across the cooling system.
Long time R&D partner and high-horsepower BMW engine specialist, RK Autowerks, approached CSF in early 2020 about developing McLaren 720S Intercoolers that they were in the midst of designing.
Above: 3D engine scans with OEM intercooler position with an overlay of the initial concept design by RK Autowerks.
Once RK Autowerks had fully utilized all of the available space within the engine compartment to maximize the size of the initial intercooler design, CSF then produced a prototype single piece high-performance air-to-water bar/plate intercooler core.
Our next step was to cut the prototype inlet and outlet end tanks and water-side end plates from 6061 aluminum bar stock. These tanks were optimized using SOLIDWORKS flow simulation software during development.
Comparison photos showing the massive difference between the CSF prototype intercooler (left) and OEM McLaren intercooler (right). Also highlighting the larger volume/smoother end tanks of the CSF 100% TIG-welded intercooler vs. the weaker brazed/crimped OEM unit (shown pre-welded). CSF’s Intercooler Kit is also a preventative maintenance upgrade, as the factory cooling system can leak overtime at the core-to-tank crimped seam. This can cause serious issues, including anything from mild to catastrophic engine damage or failure.
The initial prototype set was sent to Southern Florida McLaren specialist, Excell Racing, for fitment and performance testing.
VooDoo Design & Engineering
Owner of Voodoo Design & Engineering, Eric Cheney, has been a long-time industry friend to CSF. Eric’s skillset is extremely unique in the high-performance automotive industry, as he is both an excellent fabricator as well as a motorsports engineer. Being local to CSF as well as in the center of Southern California, a global hot spot for McLaren tuning, Eric was consulted to not only further improve the design into a production-ready kit, but to also handle all fabrication and assembly.
Behind-the-scenes of fabrication and further development of the McLaren 720S Intercooler Kit, between Eric Cheney, of VDE, and Ravi Dolwani, Owner of CSF Race.
CSF’s second revision prototype intercooler installed on SSR Performance’s 1,000HP 720S, tuned by M Engineering.
The final piece to the puzzle, and arguably the most important to this project’s development, has been CSF’s new partnership with M Engineering of Southern California – the number one McLaren tuner in the world and holders of numerous McLaren world records.
M Engineering was approached by CSF to not only validate the performance of the intercoolers, but to also take on distribution of the new intercooler kit through their global network of McLaren specialty tuning companies.
Below are charts compiled by M Engineering during their extensive dyno testing. The charts show the increased performance benefits of the CSF 720S Intercooler Kit vs. the OEM Intercoolers during 5th gear pulls.
CSF’s core technology is also more resistant to heat soak compared to the OEM plate-type intercooler core. Not only is the core proven to lower IATs, but also maintains a more consistent lower average temperature – this is ideal for achieving optimal performance on vehicles with larger/upgraded turbochargers as well as maintaining maximum efficiency during racing or demanding driving conditions with repeated pulls such as at the drag strip or half-mile events.
Performance testing resulted in lower outlet air temperatures from the CSF Intercoolers, showing almost no increase in intake air temperatures during the entire course of the dyno pull (orange line on the CSF graph on the right-hand side shows improved and consistent performance in intake air temperatures).
Not only do the CSF Intercoolers perform better than the OEM, but also decreased the pressure drop at high air mass flow as well. The OEM intercooler system resulted in approximately 1.0psi of pressure drop vs. the improved performance of CSF’s upgraded intercooler kit showing approximately 0.75psi of pressure drop.
After almost one year of development, CSF is proud to release its much anticipated McLaren 4.0L High-Performance Intercooler Kit, allowing McLaren tuners and owners the ability to lower intake air temperatures, maximize turbo efficiency, and increase boost pressure in their pursuit of the fastest speeds in the world.
As these units are all hand made with multiple specialty components, initial quantities are extremely limited.
High-Performance Intercooler Kit – CSF #8186
- Custom-Spec High-Performance CSF Bar/Plate Core Built In-House
- 68% Increase in Core Volume vs. OEM
- Single-Core Dual-Pass Design vs. Inefficient Multiple Core Design Found in Competitors Lower Quality/Less Efficient Offerings
- Efficiency Tested at 99% by M Engineering vs. OEM 94%
- Pressure Tested to 4bar (58psi)
- CNC Machined 6061 Aluminum Billet End Tanks Designed and Produced by RK Autowerks
- Finished in CSF’s Aerospace-Grade Thermal Dispersion Space Grey Coating for Maximum Heat Transfer Efficiency and OEM+ Aesthetic
- Integrated Dual 1/8-NPT Methanol Injection Bungs Positioned on Outlet Tank for Post-Intercooling Reduction of IATs
- Come Pre-Plugged For Vehicles Without Methanol Injection
- Can Also Be Used As Sensor Ports
- Complete Drop-in Fit Package With No Modifications Required for Installation
- Can Be Installed From the Rear Wheel Well Without Removing the Downpipes
- Includes Laser-Cut Machined Brackets and Reinforced Silicone Couplers for Throttle Body Connections
- Made in the USA
- 2017+ McLaren 720S
- 2021 McLaren 765LT
- 2019+ McLaren Senna
- 2019+ McLaren GT
- MSRP/MAP $5995 USD
Disclaimer: This product is an aftermarket product sold “as is” with no warranty whatsoever. The entire risk as to the quality and performance of such parts is with the buyer. Should such parts prove defective following their purchase, the buyer and not the manufacturer, distributor or retailer, assumes the entire cost of all necessary servicing or repair. The entire risk as to the performance of such parts or vehicles is with the buyer.
To the fullest extent allowed by the state and federal law, CSF, Inc. expressly disclaims the implied warranties of merchantability and of fitness for a particular purpose, even if a particular purpose is mentioned herein. CSF, Inc. also expressly disclaims all liability for direct, indirect, special, incidental, or consequential damages, including but not limited to, damage or loss of property or equipment, loss of profits or revenue, cost of purchase or replacement of goods, or claims of customers of the purchaser that result from the use of parts contained on this webpage. In no event shall the liability of CSF, Inc. whether in tort, contract or otherwise, exceed the cost of the part or vehicle. However, you may have legal rights that vary from state to state.